Skip to main content

Some propeller repairs you can do yourself!

By

DIY PROP REPAIRS

Three DIY propeller maintenance tasks to keep your wheels turning.


Unless you are an expert welder who also happens to have access to a hydraulic press, the chances of your completing a major propeller repair or reconditioning job successfully are slim and none. And Slim doesn’t work here anymore.

DIY Prop Repairs
That doesn’t mean you shouldn’t perform minor repair and maintenance. After all, even small imperfections can impact performance and the mechanical integrity of your driveline.
Here are three DIY propeller maintenance tasks.

Fixing a Ding


 Perhaps you whacked flotsam or jetsam at night, or maybe you too enthusiastically chased the school of fish into the boulder garden. Whatever. Your propeller now has a moon-shaped bend in the edge of one blade. You can likely make the propeller usable until you can send it out for recon. You’ll need two adjustable wrenches — aka crescent wrenches — to complete this task.
Affix the jaws of one wrench on the edge of the blade adjacent to the dinged area. Affix the jaws of the other wrench onto the ding itself. Holding the first wrench firmly to prevent the entire blade edge from bending, slowly apply pressure to the wrench on the ding. You should be able to work most, if not all, of the unfairness out of the blade edge.

Filing Burrs


 The edge of a prop’s blade gets burred — or rolled over — when the prop rotates through sand. Up close, the prop may look finely saw-toothed right on the blade edge. By rubbing the tip of your thumb over the edge, you can feel the burr.
A hardware store mill bastard file can help you remove the burr and return the edge of the blade to fair, so that less air is generated and water is released smoothly once again. Working from the back of the blade toward the edge, hold the file at as steep an angle as possible to help ensure that you remove as little material as possible. You will be removing some metal — and thus changing the size of the blade minutely. Every few strokes, check for the burr with your thumb, like you would when sharpening a knife. Again as with a knife, stop when you are done (the burr is no longer felt).

Spun Hub or...


 Outboard propellers are fitted with an inner hub made of a material designed to shear away upon heavy impact, and so protect the drivetrain from shock damage. When the hub shears, it’s known as “spinning the hub.” Usually, there is enough friction with a spun hub to allow you to operate the engine at low rpm. But when you try to get on plane, the tach rises and the water churns but the boat doesn’t accelerate because the shaft is spinning in the hub. This is how it’s meant to work — the low-rpm friction providing the ability to get home.
But how do you know if your hub is spun or you are having some other problem with the same high engine speed/low boat speed symptoms? Sometimes, a hub hasn’t fully broken but is only on the way out, and the symptoms come and go. So how do you know?
One way is to place a mark or scratch across the inner and outer hub with nail polish, a marker or an awl. If you’ve spun a hub, a simple visual inspection will show your line or scratch as broken.

Marking a prop hub to indicate a "spun hub."
Labels:

Comments

Post a Comment

Popular posts from this blog

Pirates have tried to invade a ship, look what happened!

By
Pirates have tried to invade a ship, look what happened! A small band of Somali pirates attempt to seize an unidentified ship during a raid. Bad idea. The ship turns out to be a U.S. Naval vessel. Watch what happens. Piracy in international waters is down in recent years, as governments and private shipping have gotten wise to the tactics of the raiders of the high seas. Pirates are finding increased patrols, harder targets, and tougher reprisals ( like this ), which has resulted in far fewer hijackings, according to statistics from the International Chamber of Commerce. This is a good thing, of course. But it also means we're going to see far fewer of these highly entertaining videos. Watch what happens when these tough guys see that they are not raiding a helpless commercial vessel but one owned and operated by the U.S. Navy. It's what you call a classic "oh sh*t" moment. Enjoy :
2 comments
Read more

What's the difference between a cruiser, a destroyer, a frigate, and a littoral combat ship?

By
This is meant to be a general overview of each of these ships and their capabilities, not looking at specific information such as size and armament (which can easily be found online, if you want specific facts about each ship).  Littoral Combat Ship (LCS):  One of the newest types of ships, made up of the Freedom and Independence Classes with only 3 ships in service. LCS's are very small, versatile ships that were created with the aim of extending the Navy's capabilities closer to the shore. LCS's are made to operate in shallower water than most USN platforms and have different modules that can be swapped in and out depending on the mission requirements.  Cruiser (CG):  Cruisers are now becoming less and less relevant, with only 22 left in the Ticonderoga-Class. Their main focus is to provide the Navy with a multi-functional guided missile platform (launching weapons systems such as the Tomahawk and other missiles via the ship's vertical launching system ...
Post a Comment
Read more

Who the hells filming this!?

By
Been there, done that in a 2100 ton, 300 ft. destroyer, the USS Van Valkenburgh, DD-656, in 1952. As I tell the story, the Captain asked me, "How do we turn around in this sea? We have to come about (turn around) to get out of this typhoon." I told him, "Simple. As you ride up the 60-foot wave, put the starboard screw on all-back-full, and the port screw on all-ahead-full. Just as you reach the crest of the wave, put 'er on hard right rudder! Don't forget to put the helm amidships and both screws on full ahead when you start down the other side of the wave.  Then when the ship starts accelerating down into the trough, slow the screws down to about half power." He did that, we came smartly around 180 degrees, plowed into the wave now in front of us, steadied, and rode back out of the storm." I asked the Captain to give full credit to the helmsman and the two engine-room mates on the port and starboard throttles. He asked me how I knew...
Post a Comment
Read more